Rat Perforin ELISA Kit
 ( used in serum, plasma, cell culture supernatants and other biological fluids )
principle
This experiment used double antibody sandwich ABC-ELISA. The anti-rat Perforin monoclonal antibody was coated on the microtiter plate, and the standards and samples of Perforin were combined with the monoclonal antibody, and biotinylated anti-rat Perforin was added to form an immune complex attached to the plate, horseradish peroxidation. Enzyme-labeled Streptavidin is combined with biotin, the substrate working solution is blue, and finally the stop solution sulfuric acid is added. The OD value is measured at 450 nm. The Perforin concentration is proportional to the OD value. The standard curve can be used to obtain the specimen in the Perforin sample. concentration.
Kit composition ( 2-8 ° C preservation)
Coated Wells | 96 holes | Enzyme Conjugate | 12ml |
10× specimen dilution (Sample Buffer) | 12ml | 20×Wash Buffer | 50ml |
Standards: 80ng / bottle | 2 bottles | Substrate working fluid (TMB Solution) | 12ml |
Primary antibody working solution (Biotinylated Antibody) | 12ml | Stop Solution | 12ml |
Prepare reagents and collect blood samples
1. Collection of specimens: serum, plasma (EDTA, citrate, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc., as early as possible, stored at 2-8 ° C for 48 hours; longer time must be frozen (-20 °C or -70 °C) Save to avoid repeated freezing and thawing.
2. Standard solution preparation: Add 4 ml of distilled water before use and mix well to prepare a 20 ng/ml solution. Set the standard tube 8 tube, the first tube plus the standard dilution 900ul, the second to the eighth tube to add the sample dilution 500ul. Add 100 ul of 20 ng/ml standard solution to the first tube, mix and aspirate 500 ul with the sampler, and transfer to the second tube. Repeat the dilution as described above, and remove 500 ul from the seventh tube and discard it. The eighth tube is a blank control.
3. The 10× specimen dilution was diluted 1:10 with distilled water (example: 1 ml concentrated dilution + 9 ml distilled water).
4. Washing solution: diluted 1:20 with distilled water (example: 1 ml concentrated washing solution added to 19 ml of distilled water)
Test procedure
1. Loading: Add 100 ul of standard or sample to be tested in each well. Mix the reaction plate thoroughly and let it stand at 37 °C for 120 minutes.
2. Wash the plate: Wash the plate thoroughly with washing solution 4-6 times, and dry it on the filter paper.
3. Add 100 ul of the first antibody working solution to each well. The reaction plate was thoroughly mixed and placed at 37 ° C for 60 minutes.
4. Wash the board: the same as before.
5. Add 100 ul of enzyme-labeled antibody working solution per well. The reaction plate was placed at 37 ° C for 30 minutes.
6. Wash the board: same as before.
7. Add 100 ul of substrate working solution per well, set 37 The reaction was carried out in the dark at °C for 15 minutes.
8. Add 100 ul of stop solution to each well and mix.
9. Measure the absorbance at 450 nm using a microplate reader within 30 minutes.
Result calculation and judgment
1. All OD values ​​should be subtracted from the blank value before calculation.
2. Take the standard products 2000, 1000, 500, 250, 125, 62.5, 31.2, 0 pg/ml as the abscissa and OD as the ordinate. Draw on the coordinate paper and draw the standard curve.
3. Find the corresponding Perforin content on the graph based on the OD value of the sample.
Kit performance
1. Sensitivity: The minimum Perforin detection concentration is less than 16pg/ml.
2. Specificity: Recombinant or natural rat Perforin can be tested simultaneously. Does not cross-react with other cytokines in rats.
3. Repeatability: The coefficient of variation in the plate and plate is less than 12%.
Precautions
1. It is recommended to make double holes for the above standard holes and samples to be tested. The standard curve should be made at the same time for each measurement.
2. The washing process is critical. Insufficient washing will result in an accuracy error and an erroneous rise in the OD value.
3. After the slats are opened, the remaining slats should be sealed again to keep the slats dry .
4. This kit should be stored in a 4 o C refrigerator.
5. This kit is for scientific research only and cannot be used for clinical diagnosis!
Traffic Signal Controller
Welcome to use traffic signal controller. It is independently developed by our company and is up to the public safety industry standards GA47-2002 <Traffic signal controller> of People's Republic of China. The traffic signal can control traffic signals in one independent intersection and meet your various demands to ensure easy and convenient traffic management.
Product Advantages:
Various control modes for your choice
Such as multi-periods, projects, yellow flashing.
1.Perfect pre-sales and after-sales service for your satisfaction
ï‚«The simulation intersection matches with real intersections, which is easy for users to set parameters.
2.Wires are placed on a high position to ensure electrical safety in case of heavy rain
3.Easy to set the parameters
4.Simple wiring methods classified according to East, South, West and South directions.
5.Different protection functions including electric leakage protection, lightning protection, output short-circuit protection, high current shock protection.
6.Operation instruction Video for helping understanding
Automatic detection of green conflict during setting process in case of real-time green conflict.
Functional Features:
1.Built-in central control system to ensure work stability
2.Weather-proof out-door cabinet with lightning-protection and power supply filter devices.
3.Easy for maintenance and function extension by adopting modular design
4.44 outputs and 16 light groups with work current of 10A
5.Extensible RS-232.RS-485 interface to communicate with upper computer
6.Able to adjust, check and set while working
7.2*99 work periods for workday and holiday setting
8.32 working menus used for any period
9.Each menu can include 99 steps and 1~255s each step
10.The flashing state, frequency and time of each signal light can be set or adjusted.
11.Flashing time and frequency can be adjusted according to needs.
12.Able to enter yellow flashing state at any time in case of emergency
Manual control can be achieved by specific menu or while under working.
Led Traffic Light Controller,Traffic Light Controller,Remote Control Traffic Light Controller,Intelligent Traffic Light Controller
Shenzhen Wide Way Optoelectronics Co., Ltd. , https://www.wdmtrafficlight.com